PFA monitors press process by waveform
OK/ NOK judgement with 2 sensor inputs
¡öMulti-point judgment
Templates are available for frequently used sequence.
Screw tightening management template compliant to torque method & turning angle method is also available.
Sensor input | |
Fixed as strain gauge input(6-wire) | |
Excitation voltage |
DC2.5, 5, 10V±10%£¨depending on settings) Output current: Within 30mA |
---|---|
Signal input range | -2.0mV/V to +2.0mV/V |
Accuracy |
Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input) Zero drift: Within 0.2μV/¡æ RTI Gain drift: Within 15ppm/¡æ |
Low-pass filter | Selectable from 2 to 2kHz£¨£6dB/oct.£© |
A/D converter |
Speed: 5000 times/sec. Resolution: 24bit (binary) |
Voltage input | |
Signal input range | -10 to +10V |
Input impedance | App. 1MΩ or more |
Accuracy |
Non-linearity:Within 0.02%/FS ±1 digit (at 10V input) Zero drift:Within 0.2mV/¡æ RTI Gain drift:Within 0.01%/¡æ |
Low-pass filter | Selectable from 2 to 2kHz£¨£6dB/oct.£© |
A/D converter |
Speed: 5000 times/sec Resolution:24bit Effective |
Sensor input¡¡Sensor input for displacement Pulse input (Line driver) |
|
Max. input frequency | 1MHz |
Internal count range | 30bit |
Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Output stage circuit specification£ºLine driver (based on RS-422A) |
Analog voltage output | |
Output level | Approx. 2V per 1.0mV/V input |
---|---|
Load resistance | 2kΩ or more |
Display section | |
Display | 7.0 inch TFT color LCD module |
---|---|
Display section |
Display area: 152£¨W£©×91£¨H£©mm Dot configuration: 800×480 dot Language:Japanese, English, Chinese |
COMP. & JUDGE. function | |
Multi point comparison mode 256ch (setting values can be stored) |
Capable of judging up to 5 hold points at the same time. Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End |
---|---|
Waveform comparison mode 256ch (setting values can be stored) |
Compares the actually measured waveform against the preset Hi/Lo waveforms. The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK. |
Preventive maintenance support | |
Trend display | Trend analysis of measured data & detect irregularities at early stage. |
---|---|
Statistics |
Takes judgement results of latest data (10,000) Displays measurement count, OK/NOK ratio |
Screen capture | Saves screen capture data as bmp data. |
Editable work name | Work name can be edited and displayed for each Work No.. |
Setting list display | Distinguish master setting & current setting with color. |
User management | Register multiple login IDs and password |
External signal | |
Output signal 16 points |
Hold judgement (force, stroke)/ Force overload/ Measurement complete/ Waveform comparison/ Force・stroke OK/ CPU OK/ SD card OK/ Timing output 1,2/ Servo ready/ Motor alarm/ In position/ Brake off/ Torque limit/ Zero speed/ General-purpose output/ Sequence in progress/ Return origin complete/ POT(Forward rotation lock)/ NOT(Reverse rotation lock) *Selectable from the above Output type: select PNP or NPN (Need to specify) Rated voltage: 30V, Rated current: 30mA |
---|---|
Input signal 16 points |
Force zero/ Stroke adjust/ Measurement start/ Measurement stop/ HOLD 1 to 5/ Reset/ Backlight forced ON/ Touch panel lock/ Work selection/ Servo on/Start sequence/Stop sequence/Pulse clear/Alarm clear/ Forward rotation lock/Reverse rotation lock/General-purpose input/ Home position detect/Return to home position/Home position/ JOG£«/ JOG£/ STEP£«/ STEP£ *Selectable from the above Input type: select PNP or NPN (Need to specify) |
Motor control | |
Compatible servo amplifier | Require pulse input. |
---|---|
Sequence function |
Configurable press-sequence in PFA Switchable control modes in sequence Control program 256 presets (Setting values can be stored) Up to 100 lines can be registered into 1 control program |
PFA <=> Servo amplifier connection |
Pulse for position control (Line driver) (based on RS-422A) Max 500k Pulse/sec Digital I/O: Control usage |
Command |
Motor operation£ºPosition control / Force control/ Stand-by/ keep Control character£ºBlank/ Jump/ If/ Watch/ Out put/ Judge/ Timer/ Counter Graph£ºGraph color display/ Delete graph Record£ºStart measurement/ Stop measurement/ Start hold/ Stop hold Motor parameter£ºSpeed/ Position gain/ Force gain Row£ºInsert above/ Insert below/ Delete row Digital offset£ºX/Y |
External devices | |
Barcode Reader(USB) | Scan items |
---|---|
SD Card | Measured data・waveform can be saved (CSV) |
Interface Only one option can be installed. |
|
USB | USB interface |
---|---|
ETN | Ethernet interface (option) |
ODN | DeviceNet interface (option) |
CCL | CC-Link interface (option) |
EIP | EtherNet/IP interface (option) |
General performance | |
Power supply voltage | DC24V£¨±15£¥£© |
---|---|
Power consumption | 20W typ. |
Operation condition |
Operation temperature: -10¡æ to +40¡æ/ Storage tempe rature: -20¡æ to +60¡æ Humidity: 85% RH or less (non-condensing) |
Dimensions | 218(W)x 140(H)x 87(D) mm (Projections excluded) |
Weight | Approx. 1.8kg |
CE marking certification | EMC Directives EN61326-1 |
Attachments | |
Analog connector | 1 |
---|---|
SD card 16GByte | 1 |
Operation manual | 1 |
DeviceNet connector (when DeviceNet option is selected)£© | 1 |
CC-Link connector (when CC-Link option is selected) | 1 |
Option
Model | |
ODN | DeviceNet interface |
---|---|
CCL | CC-Link interface |
EIP | EtherNet/IP interface |
ETN | Ethernet interface |
Optional accessories
Model | |
SD16G | SD card 16GByte |
---|---|
SD32G | SD card 32GByte |
PFA-ST | Supporting stand (VESA 100/75 compliant) |
PAF-CONV-PAN | Dedicated terminal block |
PFA-CONV-MIT | Dedicated terminal block |
PFA-CONV-YAS | Dedicated terminal block |
PFA-CONV-TAM | Dedicated terminal block |
PFA-CONV-SIE | Dedicated terminal block |
CA10-USB | USB Cable£¨ A-microB type£© 1.2m |
CAPF-I/O-S1M | 36p 1m cable with bare wires |
CAPF-I/O-S3M | 36p 3m cable with bare wires |
CAPF-SER-S1M | 50p 1m cable with bare wires |
CAPF-SER-S3M | 50p 3m cable with bare wires |
CAPF-I/O-W1M | 36p 1m cable with connector at both ends |
CAPF-I/O-W3M | 36p 3m cable with connector at both ends |
CAPF-SER-W1M | 50p 1m cable with connector at both ends |
CAPF-SER-W3M | 50p 3m cable with connector at both ends |
CAPF-CON-W1M | 50p 1m cable with connector at both ends |
CAPF-CON-W3M | 50p 3m cable with connector at both ends |
CN71 | CC-Link connector |
CND01 | DeviceNet connector |
Structure of product code
iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
whatsapp us now !
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
Private Policy
General Statement of Principles
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at info@ims.com.my with your request. We do not store any type of sales information.
Information Correction or Removal
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at info@ims.com.my with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.