Product Details:

Outline		EMX212S	EMX312SC	EMX512SC
Mixing capability	Mixing channels	4 Mono + 4 Stereo +Return	4 Mono + 4 Stereo	4 Mono + 4 Stereo +Return
	AUX	1 (Effect Send)	1 (Effect Send)	1 (Effect Send)
	MAIN	Stereo	Stereo	Stereo
	Input channel functions	CH1-4 Compressor; 3-band PEQ; CH5-8: 3-band PEQ	CH1-4 Compressor; 3-band PEQ; CH5-8: 3-band PEQ	CH1-4 Compressor; 3-band PEQ; CH5-8: 3-band PEQ
	On-board processors	SPX, 2x 7-band GEQ, YS Processing	SPX, 2x 7-band GEQ, YS Processing	SPX, 2x 7-band GEQ, YS Processing
I/O	Mic inputs	8	8	8
	Phantom power	+15V DC; ON/OFF	+15V DC; ON/OFF	+15V DC; ON/OFF
	Line inputs	4x Stereo	4x Stereo	4x Stereo
	Control and others	Foot switch, Stand By (All mute)	Foot switch, Stand By (All mute)	Foot switch, Stand By (All mute)
On-board amplifiers	Maximum output power @4ohms	220W/ch	300W/ch	500W/ch
	Maximum output power @8ohms	120W/ch (100V model), 130W/ch (120V model), 130W/ch (220-240V model)	190W/ch (100V model), 190W/ch (120V model), 180W/ch (220-240V model)	370W/ch (100V model), 350W/ch (120V model), 320W/ch (220-240V model)
	Output selection	L/R, L+R/Monitor	L/R, L+R/Monitor	L/R, L+R/Monitor

General Specifications

Maximum Output Power @ 0.5 % THD at 1 kHz	500 W/4 Ω; 350 W/8 Ω
Frequency Response	-3, 0, 1 dB 20 Hz-20 kHz, ref to the nominal output level @ 1 kHz
Total Harmonic Distortion	Less than 0.5 % (THD+N) +14 dB @ 20 Hz, 1 kHz, 20 kHz, GAIN control: all nominal
Hum & Noise	Equivalent Input Noise, -115 dBu, Rs = 150 Ω CH 1-4 MIC/LINE: MIC
Crosstalk	-65 dB @ 1 kHz
Input Connectors	CH 1-4: XLR and Phone; CH 5/6, 7/8: XLR and Phone; CH 9/10, 11/12: XLR and Pin
CH EQ	HIGH, MID, LOW
Phantom Power	15 V
Graphic Equalizer	7 Band (125, 250, 500, 1 k, 2 k, 4 k, 8 kHz): Main (Stereo) and Monitor
Digital Effects	SPX Digital Multi Effector (24 bit AD/DA, 32 bit Internal Processing): 16 Programs
Power Amp Mode	Main L/R, Main (L+R)/Monitor
Foot Switch	On/Off
Dimensions (W x D x H)	442 x 274 x 286 mm (17-3/8'' x 10-3/4'' x 11-1/4'')
Weight	10 kg (22 lbs.)
Power Requirements	120 V 60 Hz
Power Consumption	450 W

Input Characteristics

Input Terminals		MIC/LINE	Actual Load Impedance	For Use With Nominal	Input level
					Sensitivity *2	Position	Max. before clip
CH INPUT 1-4	XLR *3	MIC	2 kΩ	50-600 Ω Mics	-60 dBu (0.69 mV)	-35 dBu (13.8 mV)	-15 dBu (138 mV)
		LINE			-30 dBu (21.8 mV)	-5 dBu (436 mV)	+15 dBu (4.36 V)
	Phone *4	MIC	6 KΩ	600 Ω	-50 dBu (2.18 mV)	-25 dBu (43.6 mV)	-5 dBu (436 mV)
		LINE			-20 dBu (69.0 mV)	+5 dBu (1.38 V)	+25 dBu (13.8 V)
CH INPUT 5/6, 7/8	XLR *3	-	2 kΩ	50-600 Ω Mics	-60 dBu (0.69 mV)	-35 dBu (13.8 mV)	-15 dBu (138 mV)
	Phone *5	-	10 KΩ	600 Ω Lines	-20 dBu (69.0 mV)	+5 dBu (1.38 V)	+25 dBu (13.8 V)
CH INPUT 9/10, 11/12	XLR *3	-	2 kΩ	50-600 Ω Mics	-60 dBu (0.69 mV)	-35 dBu (13.8 mV)	-15 dBu (138 mV)
	RCA Pin	-	10 KΩ	600 Ω Lines	-20 dBu (69.0 mV)	+5 dBu (1.38 V)	+25 dBu (13.8 V)

*1 0 dBu is referenced to 0.775 Vrms.
*2 Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (All level controls are at
maximum position.)
*3 XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*4 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*5 Phone Jacks are unbalanced.


 OUTPUT CHARACTERISTICS

Output Terminals	Actual Source Impedance	For Use With Nominal		Output level		Connector
				Nominal	Max. before clip
SPEAKER OUT	0.1 Ω	4 Ω Speakers	EMX512SC	125 W	500 W	[A1, B1] SPEAKON
[A1, A2, B1, B2]			EMX312SC	75 W	300 W	[A2, B2] Phone Jack *2
			EMX212S	50 W	200 W
MAIN OUT [L, R]	600 Ω	10 kΩ Lines	-	+4 dBu (1.23 V)	+20 dBu (7.75 V)	Phone Jack *2
EFFECT OUT	600 Ω	10 kΩ Lines	-	+4 dBu (1.23 V)	+20 dBu (7.75 V)	Phone Jack *2
MONITOR OUT	600 Ω	10 kΩ Lines	-	+4 dBu (1.23 V)	+20 dBu (7.75 V)	Phone Jack *2
REC OUT [L, R]	600 Ω	10 kΩ Lines	-	-10 dBV (316 mV)	+10 dBV (3.16 V)	RCA Pin Jack

*1 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. 
*2 Phone Jacks are unbalanced.
 
Indent Order