Description
AN-STM-1-ETH is designed as a STM-1 level optical modem with two 155.520Mb/s optical interfaces to provide a cost-effective and flexible multi-service platform. With 4 Ethernet interfaces compatible with IEEE 802.3/802.3u standard, it is easy to implement Ethernet transmission over SDH.
AN-STM-1-ETH supports port-based VLAN and IEEE 802.1Q tag-based VLAN. By adopting ITU-T G.7041, G.7042 and G.707-compliant EOS (Ethernet Over SDH) technology and VLAN technology, each Ethernet port can employs 1~4 separate Virtual Concatenation Groups (VCG), and each VCG can be assigned to one or more Ethernet ports. The bandwidth of VCG can be flexibly configured for efficient transmission of Ethernet data over SDH network.
AN-STM-1-ETH supports NE management based on CLI command and SmartView network management platform based on SNMP_V1 and SNMP_V2 protocol, to perform excellent management such as configurations, alarm monitoring and performance statistic.
AN-STM-1-ETH is suitable for data access network on the client side. With the technology compliant to ITU-T standards, it can communicate with products from other vendors adopting the same standards.
Features
-
Optical Interface
-
Two STM-1 interfaces, SFP optical module (LC connector), hot plug-in
-
Complies with GB/T15941-1995 and ITU-T G.813 standards
-
Supports RPD (Remote Power down Detection) information sending function
-
-
Supports ALS (Automatic Leaser Shutdown) to protect operators from hurt
-
-
Ethernet Interface
-
Four LAN ports(physical port), each LAN port supports auto-negotiation, it can also be set to 10M full/half-duplex, 100M full/half-duplex mode by force
-
Four WAN ports (internal port and invisible), each WAN port employs a VCG; the total bandwidth of 4VCGs is 63 VC12 and the bandwidth of each VCG is up to 48 VC12(100Mbps)
-
The LAN and WAN ports are compatible with IEEE802.3/802.3u standard
-
Supports flow control and broadcast storm filtering control
-
Supports port-based VLAN and IEEE802.1Q tag-based VLAN
-
Supports GFP-F Encapsulation specification complying with ITU-T G.7041
-
Supports VCAT specification complying with ITU-T G.707
-
Supports LCAS specification complying with ITU-T G.7042
-
Provides both LCAS and Non-LCAS modes
-
The maximum tolerated differential delay between any two VC-12 channels is 112ms
-
-
Protection
-
Supports 1+1 path protection with switching time less than 50ms
-
Supports Automatic protection mode and manual protection mode
-
-
Management
-
Provides serial management interface(CONSOLE) and Ethernet management interface (EMU), both adopt RJ45 connector
-
Supports network management based on SDH overhead or on internal E1 channel
-
Supports NE management based on CLI command via RS232 interface or TELNET
-
Supports SmartView network management platform based on SNMP_V1 and SNMP_V2 protocol to perform excellent management
-
-
Specifications
STM-1 optical interface:
Bit rate (bps): 155M
Optic ports：2 optic SFP ports
Electric ethernet interface
Connector: RJ-45
Work mode: Support auto-negotiation and forced mode, the default is auto-negotiation
Speed: 10M/100M
Duplex: Full/half duplex
VLAN: Disable
Flow control: Default: enable
Cable: CAT-5, cross-over and straight-through auto-detect
Standard: IEEE802.3 10Base-T, IEEE802.3u 100Base-Tx
Ethernet management interface (EMU)
Bit rate: 100Mb/s
Connector: RJ45
RS232 network management interface (CONSOLE)
Baud rate: 19200
Bits: 8
Stop bit: 1
parity check: None
Electricity level: EIA-RS232 standard
Connector: RJ45
Power supply
Input DC voltage: -36～-72V DC
Input AC voltage: 100～260V AC
Power consumption: Less than 15W
Environment requirements
Working temperature: -5℃～50℃
Storage temperature: -40℃～70℃
Relative Humidity: ≤95%，no condensation
Ordering Information
|
AN-STM-1-ETH
|
STM-1 to Ethernet converter, single or multimode, or WDM up to 120 km, 48VDC or 220 AC/110 V AC.
|
BR 35106 
US 16724 
VN 4845 
MX 3447 
AR 3136 
MY 2954 
CN 2519 
GB 2358 
