HI510
Universal Process Controller

• Waterproof IP65 (Nema 4X) enclosure
• Multi-color LED status indicators & audible alarm
• Universal mounting kits available with wall, pipe, and panel mounting options (All mounting kits must be ordered separately.)
• The Modbus-compliant unit can be integrated within a Modbus-based network and connected to other industrial electronic devices. The following tasks may be accomplished remotely:
  • Monitoring, using the virtual LCD (limited to a single remote control in the entire network)
  • Setup
  • Loading the Setup configuration file to a controller

Auto-cleaning cycle

The cleaning function allows the ability to program one or more wash cycles and use the relays to activate valves, pumps or compressed air based on the type of washing that is required to maintain probes for reliable results.
 

---

Relays

Available with up to five control and one alarm electromechanical relays.

Analog Outputs

Up to four galvanically isolated analog outputs for control of pumps and valves.

Digital RS485 Output

Can daisy-chain up to 32 devices to a remote monitoring system.

Digital Inputs

Two digital inputs available for modes including disabling, cleaning and placing the controller into hold status.
 

---

Large LCD

The LCD displays measurement information along with indicators of potential problems. The DIAG key then provides details of the issue.

Data-logging

Store info at selectable intervals along with relay control settings and calibrations data.  up to 100 lots, each holding 8600 records. Transfer to a flash drive as a .csv file using the USB Type-C port.

Help Button

Using the help and diagnostic button (? DIAG) will provide information related to errors or in setup mode, information about settings.
 

---

SPECIFICATION

Specification	Detail
sku	HI510
Display	Graphic LCD, 128 x 64 pixel B/W with backlight
digital inputs	2 independent, galvanically isolated inputs, configurable for Hold & Cleaning functions On state: 5 to 24 Vdc, low or high level active
Analog outputs	2 or 4 independent outputs 0 - 22 mA configurable as: 0 - 20mA 4 - 20mA 22 mA as alarm signal
Analog output Accuracy	±0.2% f.s.
Digital Communication	RS-485 serial port for remote monitoring and control USB-C port to retrieve log files and firmware upgrades
Relays	Up to 5 relays, independently configurable for process variables, Hold and CLeaning Functions Electromechanical relay SPDT and SPST contact outputs 5A - 250 VAC, 5A - 30 Vdc (resistive load) Fuse protected: 5A, 250V slow blow
Alarm relay for all measurement alarms	Electromechanical relay SPDT contact output 5A - 250 Vac, 5A - 30 Vdc (resistive load) Fuse protected: 5A, 250V slow blow fuse
Data logging	Interval log, up to 100 files, maximum 8600 records on each stored file. When the maximum limit is reached, the most recent file with automatically erase the oldest one. Event log, maximum 100 records. When the maximum limi
Power Supply	100 - 240 Vac ± 10%, 50/60 Hz, 15VA
Power consumption	15VA
Installation category	II
Enclosure*	Single case 1/2 DIN, type 4x IP65 ingress protection
Weight	Approximately 1.6 kg, (3.5 lb.)
Dimensions	Width: 144.0 mm (5.7 in.) Height: 144.0 mm (5.7 in.) Depth: 151.3 mm (6.0 in.)
Environment	-20 to 50°C (-4 to 122°F), maximum 100% RH non-condensing
Note	*For a water tight seal, tighten the four front casing screws to 13.3 lbf-in (1.5 N-m, maximum 2.0 N-m) of torque