- Five-stage stainless steel fractionating jet purifies pumping fluid.
- Full thermal protection.
- Fluid-level sight glass provides quick indication of pump fluid level at all times.
- Fill and drain assembly for pump oil.
- Optional halo baffle cold cap reduces backstreaming without adding height.
- Standard gauge port (NW-25) below inlet flange included.
- Optional quick cool coil.
- Please note that this item is controlled for export by the Nuclear Suppliers Group. Accordingly, you may be required to obtain an export license from the U. S. Department of Commerce prior to exporting this pump from the United States. Please consult the U. S. Export Administration Regulations, ECCN 2B231, for further guidance.
Technical Specifications
|
Pumping Speed, Operating Range Pumping Speed, AVS 4.1 (1963) |
17,300 l/s Air, 21,625 l/s He and H2 32,000 l/s Air |
| Maximum Throughput | 30 T-l/s (40 mbar l/s) in operating range, 35 T-l/s (45 mbar-l/s) @ 0.01 torr |
| Operating Range | 1.7 x 10-3 to <5 x 10-8 torr (2.3 x 10-3 to <6.5 x 10-8 mbar) |
| Maximum Forepressure |
No Load: 0.50 torr (0.65 mbar) Full Load: 0.35 torr (0.45 mbar) |
| Recommended Backing Pump | ɛ300 cfm (510 m3/hr) |
| Backstreaming Rate, Standard Cold Cap | <7 x 10-4 mg/cm2/min |
| Warmup Time | 60 minutes |
| Cooldown Time | 180 minutes |
| Fluid Charge | 3 U.S. gallons (11.3 liters) |
| Electrical Requirements | 3 ph, 50/60 Hz, 240/415/480 VAC |
| Pump Power | 24,000 watts |
| Cooling Water Requirements | 4 gpm (800 l/hr) at 60-80°F (15-26°C) |
| Water Connections | 3⁄8 in. FPT Tee |
| Recommended Fluid | DC-704 |
Speed Curve Graph
Pumping Speed/Cold Cap Pumping speed/Halo Baffle Throughput
Outline Drawing
| Description | Voltage | Weight Kg (Lbs) | Part Number | |
| HS-32 Pump | Flange Type | |||
| Electrical Requirements | ASA | ISO | ||
| HS-32 with standard cold cap | 240 V | 612 (1,350) | 76134308 | L5923308 |
| HS-32 with halo baffle | 240 V | 612 (1,350) | 76134318 | L5923318 |
| HS-32 with standard cold cap | 415 V | 612 (1,350) | 76134326 | L5923326 |
| HS-32 with halo baffle | 415 V | 612 (1,350) | 76134336 | L5923336 |
| HS-32 with standard cold cap | 480 V | 612 (1,350) | 76134309 | L5923309 |
| HS-32 with halo baffle | 480 V | 612 (1,350) | 76134319 | L5923319 |
| Accessories | ||||
| Water-cooled halo baffle | 16 (35) | K1856332 | ||
| Centering ring for ISO foreline flange, 200K | 0.5 (1.0) | IC200SV | ||
| O-ring, ISO Inlet flange | 0.5 (1.0) | 78536002 | ||
| Instruction manual | 699901140 | |||
| Replacement Parts (six heaters required per pump) | ||||
| Heater*, 4000 W, 240 V/415 V/ 480 V with leads | 0.5 (1.0) | 647332010 | ||
|
Heater*, 4000 W, 240 V/415 V/ 480 V no leads used on pumps built before May 90 (*One heater consists of 2-120V heaters, right and left) |
0.5 (1.0) | 647332075 | ||
| Heater crush plate (replace one with each new heater) | 4.0 (8.0) | K7246001 | ||
| Heater insulator (one required per pump) | 0.5 (1.0) | 75792001 | ||
| Heater clamping plate (six required per pump) | K7247001 | |||
| Replacement o-ring kit for ASA pumps (kit contains: 1 inlet flange o-ring (buna 45390001), 1 foreline flange o-ring (butyl 2-443), sight glass o-ring and gasket, 8 fill and drain o-rings (Viton 2-213)) | 0.5 (1.0) | K0377167 | ||
| Sightglass service kit (pumps built before Oct. 95) | 1.5 (3.0) | F6097301 | ||
| ISO inlet flange o-ring | 78536002 | |||
| Upper (water) thermal switch (set at 550° F/288 °C) | 0.5 (1.0) | K9050005 | ||
| Lower (boiler) thermal switch (set at 220° F/104 °C) | 0.5 (1.0) | K9050004 | ||
| Cold cap gasket/grommet (kit of 4) | 0.5 (1.0) | L8839301 | ||
| Cold cap nut and follower (2 each) | 0.5 (1.0) | L8840301 | ||
| Heater Retrofit Kit (for pumps built before May 90; clamping plates not included) | ||||
| HS-32, 240 | 18.16 (40.0) | L6517308 | ||
| HS-32, 415 | 18.16 (40.0) | L6517326 | ||
| HS-32, 480 | 18.16 (40.0) | L6517309 | ||
US 969 
MY 520 
CN 123 
AU 112 
AP 80 
GB 74 
CA 63 
IE 56 
