This project focuses on designing the hardware for capturing and temporarily storing large amounts of data efficiently before transferring it to a computer or microcontroller for analysis.
Project Overview
The main goal of this project is to design a high-speed data logging module that temporarily stores incoming data at a high rate using the BS62LV4006EIP55 SRAM. The stored data can then be offloaded to a microcontroller or external memory for further processing.The data logger can be used in various applications, including:
● Capturing high-speed sensor readings (e.g., accelerometers, temperature sensors)
● Logging data from serial interfaces (e.g., SPI, I2C, UART)
● Recording digital signals for debugging purposes
Why BS62LV4006EIP55?
The BS62LV4006EIP55 is a 4M-bit (512K × 8) static RAM that features fast access time, low power consumption, and easy integration into microcontroller-based circuits. Some key features include:● Fast access time (55ns) – ideal for high-speed logging
● Low power consumption – extends battery life in portable applications
● CMOS technology – ensures stability and reliability
● Standard 32-pin SOP package – easy to integrate into a PCB
Project Components
To build this high-speed data logger, you’ll need the following components:Main Components:
● BS62LV4006EIP55 – Static RAM for high-speed data storage● Microcontroller (e.g., STM32, ESP32, or Arduino Mega) – To control read/write operations
● Analog-to-Digital Converter (ADC) module (if dealing with analog signals) – For converting sensor data into digital format
● Clock generator (if needed) – Ensures consistent timing for fast logging
Additional Components:
● Voltage regulators (3.3V and 5V) – Ensure stable power supply● Oscilloscope (for testing and debugging) – To verify signal integrity
● Breadboard and jumper wires – For prototyping before PCB fabrication
● Resistors, capacitors, and pull-up/down resistors – For signal conditioning
Circuit Design
1. Power Supply Configuration
The BS62LV4006EIP55 operates at 3.3V, so the power supply must be regulated to prevent damage. If your microcontroller operates at 5V, use a logic level shifter or voltage regulator to step down the voltage.2. SRAM Interfacing with Microcontroller
Since the SRAM has a parallel interface, it requires multiple GPIO pins for address and data lines. The basic interfacing involves:● Address bus (19 lines for 512K locations) – Controlled by the microcontroller
● Data bus (8-bit bidirectional lines) – Reads or writes data to the SRAM
● Control signals (CE, WE, OE, and UB/LB) – Manage read/write operations
A shift register or multiplexer can be used to reduce the number of required microcontroller pins.
3. Data Logging Flow
- Initialize the SRAM – Set all address and control pins to known states.
- Receive input data (from sensors or external source) – Digital or converted from analog using an ADC module.
- Write data to SRAM – Store each sample sequentially at increasing addresses.
- Monitor memory usage – Ensure data doesn’t overwrite previous entries.
- Offload data to external storage or microcontroller – Once memory is full or logging session ends.
Building and Testing
Step 1: Prototyping on a Breadboard
Before designing a PCB, it’s best to test the circuit on a breadboard:● Connect the SRAM to the microcontroller
● Ensure stable power with capacitors and voltage regulators
● Use a logic analyzer or oscilloscope to verify read/write operations
Step 2: Data Verification
Once data logging starts, verify stored values:● Read back data from SRAM and compare with expected values
● Check for signal integrity issues using an oscilloscope
● Ensure fast access time meets project requirements
Step 3: Finalizing the Design
If the prototype works correctly:● Design a PCB for a compact, reliable version
● Optimize the circuit layout to minimize interference
● Implement error checking for data integrity
Applications and Expansion Ideas
Potential Uses
● Industrial monitoring – Record machine vibrations, temperatures, or voltages.● Embedded system debugging – Capture real-time signals for analysis.
● Data acquisition systems – Store sensor readings for AI or ML applications.
Further Enhancements
● Add an SD card module – Expand storage capacity for long-term logging.● Use DMA (Direct Memory Access) with microcontrollers – Improve performance.
● Implement a wireless module (e.g., Wi-Fi, Bluetooth) – Stream data in real-time.
Conclusion
This DIY high-speed data logger using the BS62LV4006EIP55 SRAM provides an efficient way to capture and store large amounts of data in real time. With fast read/write speeds and easy interfacing, it’s ideal for applications requiring temporary high-speed storage. By following this guide, you can build and customize your own data logging system for various needs.Would you like to integrate additional features such as real-time data visualization or wireless transmission? Let me know how you’d like to modify this project!
US 19822 
GB 13928 
BR 12028 
CA 10943 
AU 9355 
IE 6036 
NZ 1588 
TR 1074 
